Technical

Vacuum Metallizing & Optical Density Explained

Quick Answer

Vacuum metallizing evaporates aluminum in a vacuum chamber so it condenses onto PET film as a layer only hundreds of angstroms thick. Optical density (OD) is −log10 of transmittance: OD 2.0 passes at most about 1% of light. Expansteel specifies aluminum OD ≥ 2.0 on ES-VM and ES-VM Plus, ≥ 1.5 on ES-H and ≥ 2.5 on ES-H03.

01 — Process

How Does Vacuum Metallizing Work?

Aluminum is evaporated inside a vacuum chamber and condenses onto a moving polyester (PET) carrier film as a continuous metal layer, typically hundreds of angstroms thick. The aluminum bonds into the film surface, producing a dense reflective layer rather than a coated-on surface treatment. Because the layer reflects light instead of absorbing it, one deposition pass can do the blackout or reflective work that would otherwise take several pigment coating passes.

Expansteel runs vacuum metallizing and non-woven lamination in-house, on 12 μm standard PET (customizable from 6 to 100 μm), in widths up to 2400 mm.

02 — Measurement

What Is Optical Density, and How Does It Map to Light Blocking?

Optical density is logarithmic: OD = −log10(T), so transmittance T = 10−OD. The table gives the theoretical maximum light passing through the metal layer alone at each OD.

Optical density (OD)Max. light transmittance (calculated)
1.010%
1.5≈ 3.2%
2.01%
2.5≈ 0.32%
3.00.1%

Values are calculated from the formula, not separate lab results. Because OD is logarithmic, small OD increases are large increases in blocking. The ES-VM Plus TDS specifies the finished film at ≈ 0% light transmittance.

03 — Expansteel Grades

Which OD Does Each Expansteel Grade Specify?

Expansteel recommends choosing the grade by application, not by OD alone: ES-VM Plus for total-blackout shade cores, ES-VM for general metallized layers and insulation, and the ES-H series where gas barrier is the job.

GradeAluminum ODOther published figuresTypical use
ES-VM≥ 2.0 (typical 2.0)Al adhesion 1.5 N/15mm; 6–100 μm customizableGeneral-purpose metallized layer, semi-blackout grades, insulation, decoration
ES-VM Plus≥ 2.0 (typical 2.0)Light transmittance ≈ 0%; UV-aging PassTotal-blackout core for cellular, pleated and roller shades
ES-H≥ 1.5OTR ≤ 1.0 cc/m²·24hEntry-tier high barrier: coffee, oxidation-sensitive snacks
ES-H03≥ 2.5OTR ≤ 0.1 cc/m²·24h; WVTR ≤ 0.3 g/m²·24hUltra-high barrier and full light block
FAQ

Frequently Asked Questions

What is vacuum metallizing of PET film?

Vacuum metallizing is a physical vapor deposition process: aluminum is evaporated inside a vacuum chamber and condenses onto a moving PET film as a continuous layer only hundreds of angstroms thick. The metal bonds into the film surface instead of being a separate sheet, which is why metallized film behaves differently from aluminum foil.

What is optical density (OD) on a metallized film TDS?

OD is a logarithmic measure of light blocking: OD = −log10(transmittance). OD 1.0 passes at most 10% of light, OD 2.0 at most 1% and OD 3.0 at most 0.1%. On the Expansteel ES-VM and ES-VM Plus data sheets the aluminum layer is reported in O.D. units with the test method GB/T15717 listed.

What OD does a film need for total blackout?

Expansteel specifies aluminum OD ≥ 2.0 for ES-VM Plus, the blackout-grade film, and the finished film is specified at a light transmittance of ≈ 0%. The OD table on this page is calculated for the metal layer alone; the ≈ 0% figure is the finished film's TDS specification.

Is a higher OD always better?

No. Match the grade to the requirement: barrier performance also depends on coating integrity and adhesion, not on OD alone, so choose by the application's oxygen, moisture and light requirements.

Can the aluminum optical density be customized?

Yes. For window-film base film Expansteel deposits to a customer-specified optical density — from a thick blackout layer (OD ≥ 2.0) to an ultra-thin translucent layer that reflects infrared while passing visible light.

Where do I find the OD figure for a specific roll?

Each ES grade's data sheet lists the aluminum layer's optical density, and a Certificate of Analysis (COA) accompanies every shipment. Download the data sheets from the TDS page or request a sample.

Response Commitment

Answered by an engineer, within 24 hours.

Every inquiry and sample request is reviewed by our technical team — lead times and sample logistics are confirmed in the first reply, within one business day.

Request a Sample →