Cellular shades, pleated shades, roller blinds, and blackout curtains all share one engineering problem — a core layer that must block light completely, laminate cleanly, and survive years of direct sun. ES-VM Plus was built for exactly this.
Window covering manufacturers choose ES-VM Plus when they need a total-blackout core layer: a 12 μm vacuum-metallized PET film with ≈0% light transmittance, UV-aging tested, and surface tension tuned for non-woven lamination. It ships as roll film, or as a ready film-plus-non-woven blackout composite, in web widths up to 2400 mm.
Hotel, hospital, and bedroom shade programs specify full blackout. ES-VM Plus reaches ≈ 0% light transmittance — the film itself is the blackout layer, so grade consistency does not depend on coating passes.
Shades face direct sunlight for their whole service life. The aluminum layer passes UV-aging testing — resistant to oxidation and discoloration, protecting both blackout performance and appearance.
Surface tension is tuned for lamination (AL side ≥ 48 mN/m, non-Al side ≥ 44 mN/m). We also laminate with non-woven fabric in-house and can ship a ready blackout composite — one roll, one supplier.
| Grade | Key Spec | Why It Fits |
|---|---|---|
| ES-VM Plus | ≈ 0% transmittance · UV pass | The blackout core for cellular, pleated, and roller shades |
| ES-VM | OD ≥ 2.0 · 6–100 μm | General-purpose metallized layer for semi-blackout grades |
| Item | Test Method | Unit | Standard | Typical |
|---|---|---|---|---|
| Light Transmittance | — | % | ≈ 0 | ≈ 0 |
| Weather Resistance (UV aging) | — | — | Pass | Pass |
| Thickness | GB/T6672 | μm | 12 | 12 |
| Al Thickness | GB/T15717 | O.D. | ≥ 2.0 | 2.0 |
| Density | GB/T1033 | g/cm³ | — | 1.4 |
| Al Adhesion | BB/T0030 | N/15mm | — | 1.5 |
| Surface Tension (Al side) | GB/14216 | mN/m | ≥ 48 | 54 |
| Surface Tension (non-Al side) | GB/14216 | mN/m | ≥ 44 | 46 |
| Heat Shrinkage MD (150°C/30min) | — | % | ≤ 3.0 | 1.53 |
| Heat Shrinkage TD | — | % | ≤ 3.0 | -0.45 |
| Tensile Strength MD | GB/T13022 | MPa | ≥ 170 | 241 |
| Tensile Strength TD | GB/T13022 | MPa | ≥ 170 | 233 |
| Elongation MD | GB/T13022 | % | ≥ 80 | 132 |
| Elongation TD | GB/T13022 | % | ≥ 80 | 116 |
| Max web width | — | mm | ≤ 2400 | — |
Aluminum is deposited onto 12 μm PET (customizable 6–100 μm) to optical density ≥ 2.0. This single layer is what blocks the light (≈0% transmittance).
Shipped surface tension is ≥ 48 mN/m on the aluminum side and ≥ 44 mN/m on the non-aluminum side, so adhesive bonds to both faces.
Route A: you receive the film roll and laminate it yourself. Route B: Expansteel laminates the film to non-woven in-house and ships one blackout composite roll.
Face fabric / metallized film core / non-woven backing is converted into cellular, pleated or roller shades. The film is the blackout core; the finished shade stays yours.
It is an upstream material: a vacuum-metallized PET film that shade and curtain manufacturers laminate between a face fabric and a backing layer to build their own blackout composite. It is not a finished curtain or shade.
ES-VM Plus is specified at a light transmittance of ≈ 0% with an aluminum optical density of ≥ 2.0 (typical 2.0). Because the aluminum layer reflects light, one metallizing pass does the blackout work instead of several coating passes.
The aluminum layer is UV-aging tested (result: Pass) for resistance to oxidation and discoloration, so the reflective layer is designed to keep its blackout performance over the shade's service life.
Surface tension is tuned for lamination: ≥ 48 mN/m on the aluminum side and ≥ 44 mN/m on the non-aluminum side (typical 54 / 46). Expansteel also runs its own non-woven lamination line and can supply the finished composite.
12 μm is the standard gauge and thickness is customizable from 6 to 100 μm. Maximum web width is 2400 mm; width and length are customizable to order.
Use ES-VM Plus when the spec is total blackout (hotel, hospital, bedroom programs). ES-VM is the general-purpose metallized layer for semi-blackout grades.
No. Expansteel supplies the functional film, or a film-plus-non-woven composite, to window covering manufacturers. Dyeing, face fabric and the finished shade stay with the manufacturer.
Download the ES-VM Plus TDS from the product page, or send the four-field sample request form; an engineer replies within 24 hours.
Every inquiry and sample request is reviewed by our technical team — lead times and sample logistics are confirmed in the first reply, within one business day.
Request a Sample →